AUTHORITY: Implementing Sections 9 and 10 and authorized by Sections 27 and 28 of the Environmental Protection Act [415 ILCS 5/9, 10, 27, and 28] and Section 13C-20 of the Vehicle Emissions Inspection Law of 2005 [625 ILCS 5/13C-20].
SOURCE: Adopted as Chapter 2: Air Pollution, Part VII: Mobile Sources, filed and effective April 14, 1972; codified at 7 Ill. Reg. 13628; amended in R85-25, at 10 Ill. Reg. 11277, effective June 16, 1986; amended in R90-20 at 16 Ill. Reg. 6184, effective April 7, 1992; amended in R94-20 at 18 Ill. Reg. 18013, effective December 12, 1994; amended in R94-19 at 18 Ill. Reg. 18228, effective December 20, 1994; amended in R98-24 at 22 Ill. Reg. 13723, effective July 13, 1998; expedited correction at 22 Ill. Reg. 21120, effective July 13, 1998; amended in R01-12 at 24 Ill. Reg. 19188, effective December 18, 2000; amended in R01-8 at 25 Ill. Reg. 3680, effective February 26, 2001; amended in R02-8 at 25 Ill. Reg. 16379, effective December 18, 2001; amended in R11-19 at 35 Ill. Reg. 5552, effective March 18, 2011; amended in R12-12 at 36 Ill. Reg. 1066, effective February 1, 2012.
SUBPART A: DEFINITIONS AND GENERAL PROVISIONS
Section 240.101 Preamble
As the state of knowledge and technology relating to the control of emissions from motor vehicles advances, and in furtherance of the purposes of the Environmental Protection Act [415 ILCS 5] (Act), the Pollution Control Board (Board) shall provide by rules and regulations for the control of emissions from motor vehicles. Such rules and regulations shall prescribe requirements for the installation and use of equipment designed to reduce or eliminate emissions and for the proper maintenance of such equipment and of vehicles. Any rules and regulations promulgated pursuant to this Section shall be consistent with provisions of federal law, if any, relating to control of emissions from the vehicles concerned.
(Source: Amended at 18 Ill. Reg. 18228, effective December 20, 1994)
Section 240.102 Definitions
All terms that appear in this Part have the definitions specified in this Section, the Vehicle Emissions Inspection Law of 2005 [625 ILCS 5/13C], and 35 Ill. Adm. Code 201 and 211. When conflicting definitions occur between this Section and 35 Ill. Adm. Code 201 or 211, the definitions of this Section apply in this Part.
"Agency" means the Illinois Environmental Protection Agency.
"Diesel engine" means all types of internal-combustion engines in which air is compressed to a temperature sufficiently high to ignite fuel injected directly into the cylinder area.
"Diesel locomotive" means a diesel engine vehicle designed to move cars on a railway.
"Evaporative system integrity test" means a test of a vehicle's evaporative system. The test shall either consist of a leak check of a vehicle's fuel cap with a fuel cap pressure decay tester (fuel cap pressure decay test), a fuel cap leak flow tester (fuel cap leak flow test), or a visual functional check, as applicable.
"Fuel cap" means a device used to seal a vehicle's fuel inlet.
"Fuel cap leak flow test" means a test which may be performed in accordance with this Part on a vehicle's fuel cap using a fuel cap leak flow tester to determine whether the vehicle complies with the evaporative system emission standards of this Part.
"Fuel cap leak flow tester" means a device used to determine the leak flow integrity of a vehicle's fuel cap by comparing the measured leak flow of the fuel cap with an established fuel cap leak flow standard.
"Fuel cap pressure decay test" means the test performed in accordance with this Part on a vehicle's fuel cap using a fuel cap pressure decay tester to determine whether the vehicle complies with the evaporative system emission standards of this Part.
"Fuel cap pressure decay tester" means a device used to determine the pressure decay integrity of a vehicle's fuel cap by monitoring the pressure behind the fuel cap for a ten second period and comparing the measured pressure decay of the fuel cap to an established fuel cap pressure decay standard.
"Fuel cap visual functional test" means the test performed in accordance with this Part on a vehicle's fuel cap using visual analysis to determine whether the vehicle complies with the evaporative system emission standards of this Part.
"Gross vehicle weight rating" or"GVWR" means the value specified by the manufacturer as the maximum design loaded weight of a single vehicle.
"Heavy duty vehicle" means any motor vehicle rated at more than 8500 pounds GVWR or that has a vehicle curb weight of more than 6000 pounds or that has a basic vehicle frontal area in excess of 45 square feet.
"High idle" means a vehicle operating condition with engine disconnected from an external load (placed in either neutral or park) and operating at speed of 2500 ±300 RPM.
"Idle mode" means that portion of a vehicle emission test procedure conducted with the engine disconnected from an external load and operating at minimum throttle.
"Initial idle mode" means the first of up to two idle mode sampling periods during a steady-state idle mode test, during which exhaust emission measurements are made with the vehicle in "as-received" condition.
"Light duty truck 1" means a motor vehicle rated at 6000 pounds maximum GVWR or less and which has a vehicle frontal area of 45 square feet or less, and which is designed primarily for purposes of transportation of property or is a derivation of such a vehicle, or is designed primarily for transportation of persons and has a capacity of more than 12 persons, or is available with special features enabling off-street or off-highway operation and use.
"Light duty truck 2" means a motor vehicle rated between 6001 and 8500 pounds maximum GVWR and which has a vehicle frontal area of 45 square feet or less, and which is designed primarily for purposes of transportation of property or is a derivation of such a vehicle, or is designed primarily for transportation of persons and has a capacity of more than 12 persons, or is available with special features enabling off-street or off-highway operation and use.
"Light duty vehicle" means a passenger car or passenger car derivative capable of seating 12 passengers or fewer.
"Measured values" means five-second running averages of exhaust emission concentrations sampled at a minimum rate of twice per second.
"Model year" means the year of manufacture of a motor vehicle based upon the annual production period as designated by the manufacturer and indicated on the title and registration of the vehicle. If the manufacturer does not designate a production period for the vehicle, then "model year" means the calendar year of manufacture.
"Motor vehicle", as used in this Part, shall have the same meaning as in Section 1-146 of the Illinois Vehicle Code [625 ILCS 5/1-146].
"Opacity" means the percentage of light transmitted from a source that is prevented from reaching a light detector.
"Preconditioning mode" means a period of steady-state high-idle operation conducted to ensure that the engine and emissions control system components are operating at normal operating temperatures, thus minimizing false failures caused by improper or insufficient warm-up.
"Second-chance idle mode" means the second of two idle mode sampling periods during a steady-state idle mode test, preceded by a preconditioning mode and utilized as a second chance to pass idle exhaust emission standards immediately following an initial idle mode failure.
"Snap-acceleration test" means a test to measure exhaust smoke opacity from heavy-duty diesel powered vehicles in accordance with the SAE J1667 procedure, incorporated by reference at Section 240.107 of this Subpart.
"Steady-state idle test" means a vehicle emission test procedure consisting of an initial idle mode measurement of exhaust emissions followed, if necessary, by a loaded or high idle preconditioning mode and a second-chance idle mode.
"Vehicle curb weight" means the actual vehicle weight plus standard equipment and a full fuel tank.
"Visual inspection test" means a visual examination of a vehicle's malfunction indicator lamp (MIL) consisting of verifying the status of the MIL in the key-on/engine off position followed by verifying the status of the MIL in the key-on/engine on position to determine the status of the MIL and existence of an emission related malfunction with the vehicle.
(Source: Amended at 36 Ill. Reg. 1066, effective February 1, 2012)